Definition of chainplate in English:

chainplate

nounˈtʃeɪnpleɪtˈCHānplāt

A strong link or plate on the hull of a yacht or sailing ship, to which a shroud is secured.
（船侧的）系链钮，系索钮；舷侧支索扣板
Example sentencesExamples
- There would be little benefit to adding a chainplate a few inches to the port side of the tiller.
- The chainplates themselves extend as far down the bulkheads as possible, reaching just above the bench level.
- This turnbuckle fastens to the chainplate with a jaw fitting and pin, and is swaged to the wire rope stay.
- By making a hook at each end I could attach the wire to the chainplate and put a pen in the other end.
- I seem to remember someone saying that there's a better material for the chainplates than stainless.
- Now, speaking about chainplate width in particular, not enough people seem to realise how important this is.
- However, three bolts should be more than sufficient, as the old chainplates were secured with only three bolts.
- The pin shown to the right is almost certainly smaller than the hole in the chainplate allowing it to tilt.
- The forward chainplate had knifed through the foredeck.
- Paul, from photo 2 it looks like the original chainplates had 6 screws or bolts into the bulk head.
- Turnbuckles and chainplates must be angled so that loads are in a direct line with stays and shrouds.
- Sereia's chainplates were fiberglassed right into her hull, which is fine until one of them starts to rust.
- They should be large enough to project from the sides of the chainplate by a good 12 mm all round.
- Later I saw the same type of scratch on four other chainplates in approximately the same location.
- Cracking or distortion on the deck around the chainplate may indicate a misalignment problem and or a deck leak.
- Actually, one side and the ends should be packed, then the chainplate slid in and bolted in place.
- The jib rack was made from the same brass section as the chainplates, and is also 2.5’ long.
- You can buy covers that go over the chainplates on the deck that hide any Sikoflex and help reduce leakage.
- You can see these in the third photo, which shows the profile of the chainplate and backing plate.
- Here's a view of the aft port lower knee with the new chainplate temporarily clamped to it for some test fitting.

Definition of chainplate in US English:

chainplate

nounˈCHānplāt

A strong link or plate on the hull of a sailboat or sailing ship, to which a shroud is secured.
（船侧的）系链钮，系索钮；舷侧支索扣板
Example sentencesExamples
- You can buy covers that go over the chainplates on the deck that hide any Sikoflex and help reduce leakage.
- You can see these in the third photo, which shows the profile of the chainplate and backing plate.
- However, three bolts should be more than sufficient, as the old chainplates were secured with only three bolts.
- Turnbuckles and chainplates must be angled so that loads are in a direct line with stays and shrouds.
- Cracking or distortion on the deck around the chainplate may indicate a misalignment problem and or a deck leak.
- Later I saw the same type of scratch on four other chainplates in approximately the same location.
- They should be large enough to project from the sides of the chainplate by a good 12 mm all round.
- The pin shown to the right is almost certainly smaller than the hole in the chainplate allowing it to tilt.
- I seem to remember someone saying that there's a better material for the chainplates than stainless.
- Actually, one side and the ends should be packed, then the chainplate slid in and bolted in place.
- Paul, from photo 2 it looks like the original chainplates had 6 screws or bolts into the bulk head.
- By making a hook at each end I could attach the wire to the chainplate and put a pen in the other end.
- Now, speaking about chainplate width in particular, not enough people seem to realise how important this is.
- The chainplates themselves extend as far down the bulkheads as possible, reaching just above the bench level.
- The forward chainplate had knifed through the foredeck.
- The jib rack was made from the same brass section as the chainplates, and is also 2.5’ long.
- There would be little benefit to adding a chainplate a few inches to the port side of the tiller.
- Sereia's chainplates were fiberglassed right into her hull, which is fine until one of them starts to rust.
- Here's a view of the aft port lower knee with the new chainplate temporarily clamped to it for some test fitting.
- This turnbuckle fastens to the chainplate with a jaw fitting and pin, and is swaged to the wire rope stay.

词汇	chainplate
释义	Definition of chainplate in English: chainplate nounˈtʃeɪnpleɪtˈCHānplāt A strong link or plate on the hull of a yacht or sailing ship, to which a shroud is secured. （船侧的）系链钮，系索钮；舷侧支索扣板 Example sentencesExamples There would be little benefit to adding a chainplate a few inches to the port side of the tiller. The chainplates themselves extend as far down the bulkheads as possible, reaching just above the bench level. This turnbuckle fastens to the chainplate with a jaw fitting and pin, and is swaged to the wire rope stay. By making a hook at each end I could attach the wire to the chainplate and put a pen in the other end. I seem to remember someone saying that there's a better material for the chainplates than stainless. Now, speaking about chainplate width in particular, not enough people seem to realise how important this is. However, three bolts should be more than sufficient, as the old chainplates were secured with only three bolts. The pin shown to the right is almost certainly smaller than the hole in the chainplate allowing it to tilt. The forward chainplate had knifed through the foredeck. Paul, from photo 2 it looks like the original chainplates had 6 screws or bolts into the bulk head. Turnbuckles and chainplates must be angled so that loads are in a direct line with stays and shrouds. Sereia's chainplates were fiberglassed right into her hull, which is fine until one of them starts to rust. They should be large enough to project from the sides of the chainplate by a good 12 mm all round. Later I saw the same type of scratch on four other chainplates in approximately the same location. Cracking or distortion on the deck around the chainplate may indicate a misalignment problem and or a deck leak. Actually, one side and the ends should be packed, then the chainplate slid in and bolted in place. The jib rack was made from the same brass section as the chainplates, and is also 2.5’ long. You can buy covers that go over the chainplates on the deck that hide any Sikoflex and help reduce leakage. You can see these in the third photo, which shows the profile of the chainplate and backing plate. Here's a view of the aft port lower knee with the new chainplate temporarily clamped to it for some test fitting. Definition of chainplate in US English: chainplate nounˈCHānplāt A strong link or plate on the hull of a sailboat or sailing ship, to which a shroud is secured. （船侧的）系链钮，系索钮；舷侧支索扣板 Example sentencesExamples You can buy covers that go over the chainplates on the deck that hide any Sikoflex and help reduce leakage. You can see these in the third photo, which shows the profile of the chainplate and backing plate. However, three bolts should be more than sufficient, as the old chainplates were secured with only three bolts. Turnbuckles and chainplates must be angled so that loads are in a direct line with stays and shrouds. Cracking or distortion on the deck around the chainplate may indicate a misalignment problem and or a deck leak. Later I saw the same type of scratch on four other chainplates in approximately the same location. They should be large enough to project from the sides of the chainplate by a good 12 mm all round. The pin shown to the right is almost certainly smaller than the hole in the chainplate allowing it to tilt. I seem to remember someone saying that there's a better material for the chainplates than stainless. Actually, one side and the ends should be packed, then the chainplate slid in and bolted in place. Paul, from photo 2 it looks like the original chainplates had 6 screws or bolts into the bulk head. By making a hook at each end I could attach the wire to the chainplate and put a pen in the other end. Now, speaking about chainplate width in particular, not enough people seem to realise how important this is. The chainplates themselves extend as far down the bulkheads as possible, reaching just above the bench level. The forward chainplate had knifed through the foredeck. The jib rack was made from the same brass section as the chainplates, and is also 2.5’ long. There would be little benefit to adding a chainplate a few inches to the port side of the tiller. Sereia's chainplates were fiberglassed right into her hull, which is fine until one of them starts to rust. Here's a view of the aft port lower knee with the new chainplate temporarily clamped to it for some test fitting. This turnbuckle fastens to the chainplate with a jaw fitting and pin, and is swaged to the wire rope stay.
随便看	entertainer entertainers entertain greatly entertaining entertaining entertainingly entertainingly entertain lavishly entertain lavishly/sumptuously entertainment entertainments entertain oneself entertains entertain the idea of entertain the idea/possibility of entertain the possibility of entertain the thought of entertain with/by enter the lists enter the lists enter the lists enter the picture enter upon enthalpies enthalpy